You're making it sticky

How to clean laminate floors

· 6 steps

Quick answer

Laminate goes sticky and dull when it gets too much water or too much cleaner: the excess dries into a film that grabs dirt and shows every footprint. Sweep or vacuum first so grit doesn't scratch it, then mop with a microfibre mop that is wrung out until it's barely damp, using warm water and a few drops of pH-neutral or laminate floor cleaner, or plain water. Work in small sections, dry any wet patch straight away, and never leave standing water at the joins. Sticky already? Go over it once more with clean water only to lift the residue, then buff dry.

⚠ Safety check

Use one product at a time and never mix cleaners. Keep the mop barely damp and never leave standing water, which can swell the boards. Don't use a steam mop unless your floor maker says it's allowed, and skip vinegar, bleach, wax, polish and abrasive powders or scouring pads, which can dull or damage the finish. Check your floor maker's care instructions first. Wipe spills as you go and watch for slippery patches while the floor dries.

Never mix cleaning products. Bleach plus ammonia, vinegar or other acids releases toxic gases. Use one product at a time, rinse between them, ventilate, and unplug appliances before you clean them.

Part of: Printable weekly cleaning checklist

Step by step

  1. Sweep, dust-mop or vacuum on the hard-floor setting (beater bar off) to lift grit and hair; grit is what scratches laminate
  2. Fill a bucket with warm water and only a few drops of pH-neutral or laminate floor cleaner, or use plain water. More cleaner is what leaves the sticky film
  3. Dip a microfibre mop, then wring it until it's barely damp; it should not drip at all
  4. Mop a small section at a time, following the length of the boards. Wipe up any wet patch or puddle straight away so water can't get into the joins
  5. Already sticky or streaky? Rinse the mop, refill with clean water only, and go over the floor again to lift the old residue
  6. Buff dry with a dry microfibre pad or towel, and keep doormats at the entrances so less grit comes in. Damp-mop once a week, sweep in between

Watch it in 21 seconds

FAQ

How to clean laminate floors?

Laminate goes sticky and dull when it gets too much water or too much cleaner: the excess dries into a film that grabs dirt and shows every footprint. Sweep or vacuum first so grit doesn't scratch it, then mop with a microfibre mop that is wrung out until it's barely damp, using warm water and a few drops of pH-neutral or laminate floor cleaner, or plain water. Work in small sections, dry any wet patch straight away, and never leave standing water at the joins. Sticky already? Go over it once more with clean water only to lift the residue, then buff dry.

What are the steps to clean laminate floors?

1. Sweep, dust-mop or vacuum on the hard-floor setting (beater bar off) to lift grit and hair; grit is what scratches laminate. 2. Fill a bucket with warm water and only a few drops of pH-neutral or laminate floor cleaner, or use plain water. More cleaner is what leaves the sticky film. 3. Dip a microfibre mop, then wring it until it's barely damp; it should not drip at all. 4. Mop a small section at a time, following the length of the boards. Wipe up any wet patch or puddle straight away so water can't get into the joins. 5. Already sticky or streaky? Rinse the mop, refill with clean water only, and go over the floor again to lift the old residue. 6. Buff dry with a dry microfibre pad or towel, and keep doormats at the entrances so less grit comes in. Damp-mop once a week, sweep in between.

Is it safe to clean laminate floors at home?

Yes, with care. Use one product at a time and never mix cleaners. Keep the mop barely damp and never leave standing water, which can swell the boards. Don't use a steam mop unless your floor maker says it's allowed, and skip vinegar, bleach, wax, polish and abrasive powders or scouring pads, which can dull or damage the finish. Check your floor maker's care instructions first. Wipe spills as you go and watch for slippery patches while the floor dries. Never mix cleaning products. Bleach plus ammonia, vinegar or other acids releases toxic gases. Use one product at a time, rinse between them, ventilate, and unplug appliances before you clean them.

More clean floors and home surfaces hacks

Quick cleaning routines